SOURCECODEBD.NET

Live Experience

Backup an IOS File from a Cisco Router

Before Starting procedure you need to download and install a TFTP server on your PC
There are many Free TFTP server just download one and install your PC.

Step 1
Create a consol connection with the default setting

Step2

Read more...

4. CONFIGURATION OF SNMP

CONFIGURATION OF SNMP
 
Interface IP Address Configuration 
 
R1 
 
Interface  IP Address   Subnet Mask 
E 1/0        50.1.1.1         255.0.0.0 

Read more...

Password Break of Cisco Router

Create a consol connection with the default setting

When its booting the IOS then hit "Ctrl+Break"
Then it will go to the ROMON Mode. it looks like

Romon>help

Read more...

5. CONFIGURATION OF NTPv3

CONFIGURATION OF NTPv3
 
Interface IP Address Configuration 
 
R1 (MASTER) 
 
Interface  IP Address   Subnet Mask 

Read more...

How to Install or Upgade Cisco IOS with Consol connection From Hyper Terminal

 
When boot the IOS just hit kebord "Ctrl+Break". You will see you are in Rommon Mode.
 
rommon 1 > confreg                  
 
do you wish to change the configuration? y/n  [n]:  y        [Type : Y, and Hit Enter]                                                
disable "diagnostic mode"? y/n  [n]:                                   [Leave "N", Hit Enter]    

Read more...

How to cofigure Cisco Time Based ACL

Router(config)#time-range work-hour
Router(config-time-range)#  absolute start 12:50 29 December 2011 end 14:05 29 December 2011
 
(Here start time 12:50 29 December 2011 and end time 14:05 29 December 2011.)

Read more...

Cisco Date and time Configuration

-> To set the time, use this command in enable mode (not configuration mode):

Router# clock set 22:45:10 June 18 2011

Read more...

2. CONFIGURING SSH SERVER FOR SECURE MANAGEMENT AND

CONFIGURING SSH SERVER FOR SECURE MANAGEMENT
 
Interface IP Address Configuration 
 
R1 
 
Interface  IP Address   Subnet Mask 
E 1/0        10.1.1.1         255.0.0.0 

Read more...

Upgrade an IOS on a Cisco Router

Before Starting procedure you need to download and install a TFTP server on your PC
There are many Free TFTP server just download one and install your PC.

Step 1
Create a consol connection with the default setting

Step 2

Read more...

Copy Running Configuration to TFTP Server

Router#copy run TFTP
Address or name of remote host []? 192.168.111.3       <-----[This is your TFTP Srever IP]
Destination filename [Router-confg]?                                <-----[Hit Enter or if you want change file name then type new file name]

Read more...

3. CONFIGURING SYSLOG LOGGING

CONFIGURING SYSLOG LOGGING
 
Interface IP Address Configuration 
 
R1 
 
Interface  IP Address   Subnet Mask 
E 1/0      10.1.1.1   255.0.0.0 
PC 1     10.1.1.2   255.0.0.0 

Read more...

Cisco_2950_IOS_Install

Step-by-Step Recovery Procedure

Use this solution to solve the problem.

Note: A PC must be attached to the console port of the switch, as the Prerequisites section of this document states.

Read more...

Reset Catalyst Switches Running Configuration Cisco

Cat2950# write erase
Erasing the nvram filesystem will remove all files! Continue? [confirm]y[OK]
Erase of nvram: complete
Cat2950#
Cat2950# reload

Read more...

Upgrade an IOS on a Cisco Router from PCMCIA Flash

Before Starting procedure you need to download and install a TFTP server on your PC
There are many Free TFTP server just download one and install your PC.

Step 1
Create a consol connection with the default setting

Step 2
Check you have enough space in your flash card

Read more...

Related Articles

You are here: Home / Knowledge Base