SOURCECODEBD.NET

Live Experience

How to show Last Time of System Booted

# run show system uptime
Current time: 2014-12-11 14:35:32 BDT
System booted: 2013-09-11 18:12:54 BDT (65w0d 20:22 ago)
Protocols started: 2013-09-11 18:14:41 BDT (65w0d 20:20 ago)

Read more...

Juniper Routes Learned from a Specific Protocol
 
You have configured a routing protocol and you want to make sure the router is learning routes from that protocol.
Include the protocol name in the show route command:

Read more...

Static Routes Configuration in Juniper
 
You want to be able to connect your router to the Internet.
Create a default static route:
 
# set routing-options static route 0.0.0.0/0 next-hop 172.16.100.1

Read more...

Juniper View Routes to a Particular Prefix
 
You need to check to make sure the local router has a route to another router in the network.
Use the following version of the show route command:
 
source@Router> show route 10.0.8.1

Read more...

Juniper Show the Routes in the Routing Table
 
You want to check the routing table to see that it contains the routes you expect to other routers in your domain and to routers in other ASs.
The show route command shows the contents of the routing table:

Read more...

How to show Last Time of configured

# run show system uptime
Current time: 2014-12-11 14:35:32 BDT
System booted: 2013-09-11 18:12:54 BDT (65w0d 20:22 ago)
Protocols started: 2013-09-11 18:14:41 BDT (65w0d 20:20 ago)

Read more...

Juniper NTP Configuration
 
You want to periodically resynchronise the time on the router to limit the effects of clock drift.
Configure the router to periodically get time updates from an NTP server:
 
# set system ntp server 192.168.100.14

Read more...

Juniper IPv6 Static Routes Configuration
 
You want to be able to connect your router to the Internet.
Create a default static route:
 
# set routing-options rib inet6.0 static route 0::/0 next-hop 3001::1

Read more...

Loopback Test on a T1 Interface in Juniper
 
A new T1 interface has been installed and configured, and you want to perform a loopback test to make sure the interface is operating properly.
Set up a T1 loopback configuration:

Read more...

Juniper Set Date and Time

This command only work from operation mode.
> set date 201406231148.00    
[Date and Time Format YYYYMMDDhhmm.ss]

Read more...

Juniper Interface Bandwidth Restriction

#set firewall policer 10mb if-exceeding bandwidth-limit 10m
#set firewall policer 10mb if-exceeding burst-size-limit 1m
#set firewall policer 10mb then discard

Read more...

Juniper Set Up a BERT Test on a T1 Interface
 
You want to run a bit error rate test (BERT) to test the quality of a T1 link.
First, configure the BERT test parameters on the local interface:
 
[edit interfaces t1-0/0/3 ]

Read more...

Juniper Monitoring Interface Traffic
 
You want to look at the headers of packets transiting an interface to debug protocol operation.
Use the monitor traffic command:
 
# run monitor traffic interface ge-1/0/1

Read more...

Juniper Failover with Static Router using qualified-next-hop
 
Use qualified-next-hop to allow independent preference for static routes to the same destination:
 
Primary next hop due to default route preference (5)

Read more...

Related Articles

You are here: Home / Knowledge Base